CO2 Laser Cutting and Engraving Machine LY-1390: Acrylic Wood and Leather
Release time:
Nov 16,2026
We at Binzhou Longfuture Machinery and Materials make this CO2 laser cutting and engraving machine as the LY-1390 model for acrylic, wood, leather and other non-metal work. The product page gives the working size, the speeds, the accuracy, the laser power options and the packing, so a buyer can compare the machine with a smaller 9060 or a larger fiber cutter. This article explains what the LY-1390 offers and what to check before an order.
The LY-1390 Working Area
The working size is 1300 by 900 mm. That table suits a standard acrylic sheet, a wood panel, a leather hide or a batch of small parts. The machine size is 1880 by 1480 by 1110 mm and the net weight is 450 kg, so the buyer should plan a door width, a floor loading and a service space around the machine before delivery.
The engraving speed is listed as 0 to 60000 mm per minute and the cutting speed as 0 to 30000 mm per minute. The position accuracy is no more than 0.01 mm. Those figures are the machine capability, not a promise for every material; the buyer should test the actual acrylic, wood or leather at the production speed before setting the process.
Laser Source and Power
The machine uses a sealed CO2 glass laser tube from Yongli. The page lists laser power options of 80 W, 100 W, 130 W and 150 W with one tube, and 300 W with two tubes. A higher power cuts a thicker material or runs a faster line, but it also needs a larger chiller and a stronger exhaust. The buyer should match the power to the thickest cut in the work.
The cooling system depends on the power. The page lists an 80 W water pump for the 80 W tube, a CW3000 for 100 W, a CW5200 for 130 W and 150 W, and a CW6000 for 300 W. The buyer should confirm the chiller, the water quality and the ambient temperature, because a CO2 tube loses power or fails when it runs too hot.
Control and Configuration
The control system is an RDC6445S, and the motor and driver are a Leadshine stepper set. The working table is a blade table plus a honeycomb table, and the table is electrically up and down. The transmission uses a linear guide and a belt. Those parts decide the smoothness of the motion and the ease of focusing for a thick or a thin material.
The machine supports PLT, DST, DXF, DWG, AI and LAS files, and it can output directly from AutoCAD and CorelDRAW. A buyer who already uses one of those programs can keep the existing design workflow.

Materials and Applications
The page lists acrylic, wood, paper, MDF board, rubber, leather, silk, stone, glass, crystal, plastic and ceramics as the materials for non-metal cutting and engraving. It names the advertising industry, the model industry, decoration, crafts and gifts, electronics, crystal ornaments, paper cutting, leather clothing, embroidery and frame production as the applications.
A buyer should test the material before a large order. A clear acrylic, a cast acrylic and a polycarbonate can behave differently under the same laser, and a leather with a coating can leave a residue on the lens. The page offers engraving samples and application pages for acrylic, clothes and wood, which are a useful starting point for a sample plan.
Installation and Safety
A CO2 laser cutter needs a 220 V supply within plus or minus 10 percent at 50 to 60 Hz, with a machine power of no more than 2500 W. The working environment is 0 to 45 degrees Celsius and 5 to 90 percent humidity without condensing water. The buyer should plan a dedicated circuit, a good earth, an exhaust duct to the outside and a dry room for the laser tube.
The machine should run with the exhaust on, the chiller at the correct temperature and the air assist set for the material. The operator should never leave a cutting job unattended, and should keep a fire extinguisher near the machine. The lens and the mirrors should be cleaned on a schedule, and the honeycomb table should be cleared of debris before a new job.
Service and Company
The page lists free online training, an overseas on-site training option that is not free, an English speaking engineer and a one year warranty that does not include the mirror and the lens. The buyer should confirm the spare parts list, the tube warranty and the response time for a service call before the order.
Binzhou Longfuture Machinery and Materials Co., Ltd. is based at 3-2-207, Macalline International Commercial Center, No.2 Xincheng Road, Boxing, Binzhou, China. The contact page lists the phone and WhatsApp +86-13884816251 and the email sales01@longfuturecnc.com. The company also offers fiber cutting machines, channel letter benders, CNC routers and laser welding machines.
Next Step
To request a quotation for the CO2 laser cutting and engraving machine, send the material, the thickness, the working size, the daily volume, the power supply and the destination. We will confirm the laser power, the chiller and the table that fit the work. A sample and a packing plan can be discussed before the order.
BLOGS UPDATE